Solenoids for parcel sorters: where they are used and how to choose them

Solenoids for parcel sorters are the actuators that turn the sorter controller’s command into mechanical movement at the exact discharge point. In a tilt tray sorter (a sorting system based on tilting trays) they release the mechanism that tilts the tray; in a shoe sorter (a high-speed sliding shoe sorting system) they divert the shoes towards the outlet; in a cross belt sorter (an automated cross-belt sorting system) they work in gates, chutes and safety interlocks.

They all share one requirement. The solenoid must respond in milliseconds, repeat the operation millions of times and do so without overheating beyond its rated range during continuous shifts.

The context explains the pressure on these components. According to the CNMC (the Spanish markets and competition regulator), 1,216.6 million parcel shipments were handled in Spain in 2024, 20% more than the previous year. Each of those parcels passes through an automated postal sorting system at least once.

What a solenoid does inside a parcel sorter

An automatic sorting system reads the parcel’s code, assigns it a destination and calculates when it will pass the corresponding outlet. The last link in that chain is an actuator that has to move at exactly the right moment.

That is where the linear solenoid comes in. When the coil is energised, the plunger moves (pulling or pushing) and actuates a mechanical element: a pawl, a diverter, a latch or a gate. When the current is cut, a spring returns the plunger to its position.

Compared with a pneumatic cylinder, the solenoid offers four functional advantages in this context:

  • Fast response over a short stroke, which is exactly what sorter diverters require.
  • Direct control from the PLC at 24 V DC, with no solenoid valves and no compressed air supply.
  • Fewer points of failure, with no leaks, no condensate and minimal maintenance.
  • Very low power consumption to carry out the required action.

Pneumatics is still the better option when high force is needed over long strokes. In sorter trigger mechanisms, strokes are usually just a few millimetres, and that is where the solenoid is the most compact solution.

Solenoids in tilt tray sorters

The tilt tray sorter moves a chain of carriers with trays around a closed loop. When a carrier reaches its outlet, the tray tilts and the parcel slides by gravity into the destination chute.

How the tray is triggered

In mechanical designs, the tray has no motor of its own. At each discharge station there is a diverter fixed to the structure and, when the target carrier arrives, a solenoid releases a pawl or a switch blade. That blade catches the roller on the tray arm and guides it along a descending ramp that tilts the tray. Further downstream, an ascending ramp returns it to the horizontal position.

This principle is described, for example, in patent US6206170B1 on the control of a tilt tray sorter, in which a vertical solenoid unlocks the diverter at each station. The rest of the movement is mechanical and does not require the coil to stay energised.

Why response time matters

Parcel sorters run at speeds of around 2–2.7 m/s. At 2.5 m/s, every 10 ms of delay equals 25 mm of carrier travel. This is why the solenoid’s ability to respond within milliseconds is decisive.

That is why, in this application, we focus above all on three parameters:

  1. Stable response time throughout the service life, not just in the first cycle.
  2. Sufficient force at the start of the stroke, which is where a linear solenoid delivers the least force.
  3. Impact resistance against the roller striking the blade, cycle after cycle.

The latest tilt trays incorporate a geared motor in each tray to control the tilt angle. In those models, the solenoid takes a secondary role, in brakes, locks or safety positions.

Solenoids in cross belt sorters

The cross belt sorter replaces the tray with a small transverse belt on each carrier. Each carrier has its own motor, which drives the belt perpendicular to the direction of travel and ejects the parcel towards the outlet. That is why the discharge itself does not depend on a solenoid.

This does not mean there are no applications. In a cross belt installation, solenoids appear in the elements surrounding the sorter:

  • Gates and flaps on destination chutes, to split one outlet into two containers or hold parcels back while the cage is changed.
  • Diverters on induction and reject lines, where unread or out-of-gauge parcels are taken out of the main flow.
  • Door and guard interlocks, which prevent access to the loop while it is moving.
  • Position holding in elements that must stay locked without power consumption, where bistable solenoids fit.

A high-capacity cross belt can exceed 10,000 items per hour per induction zone. With dozens of outlets, the number of solenoids for parcel sorters and other auxiliary actuators per installation is high, and their individual reliability weighs on the overall availability of the system.

Other parcel sorters with electromagnetic diverting

Although the discussion usually centres on tilt tray and cross belt systems, the shoe sorter, or sliding shoe sorter, is also worth mentioning. In this system, shoes slide sideways across the conveying surface and push the parcel towards the outlet.

In many designs, the change in the shoes’ path is initiated by a solenoid located beneath the surface, which attracts a ferromagnetic element of the assembly and diverts it onto the diagonal track. It is a very direct application: the solenoid must operate at a frequency set by the pitch between shoes, which is usually around 125–150 mm.

Comparison of sorters and the role of the solenoid

Type of sorter How it discharges the parcel Function of the solenoid Main requirement
Mechanical tilt tray Tilts the tray, gravity discharge Triggers the diverter at each station Response time and impact resistance
Motorised tilt tray Motor on each tray Auxiliary locks and brakes Holding without power consumption
Cross belt Motorised transverse belt Gates, reject diverters, interlocks Number of cycles and reliability
Shoe sorter Sliding shoes Initiates the shoe diversion Switching frequency

Technical criteria for choosing solenoids for postal sorting

When specifying solenoids for parcel sorters, these are the data we always ask the sorter manufacturer or the integrator for:

Stroke and force-stroke curve

The force of a linear solenoid varies with the position of the plunger. You need to check that the force available at the starting point of the movement exceeds the real load, including friction and the return spring.

Duty cycle (ED %)

In a sorter running two or three shifts, the percentage of time the coil is energised defines the operating temperature. A solenoid sized for 100% ED runs cooler, but it is larger. An alternative is overexcitation with reduction to a holding voltage, which provides more force at start-up without overheating the coil.

Service life in cycles

A tilt tray diverter can exceed several million operations a year. It is worth reviewing the plunger guide, the bushings and the damping of the end-of-stroke impact, which are the points that determine real service life.

IP rating

Parcel hubs accumulate cardboard dust and fibres. For most positions, an IP40 rating, like that of the CU Series, is sufficient; in dock areas or outdoor installations the rating will need to be higher.

Which series fit each case

  • ER Series, single-acting linear solenoids with optional spring, for short-stroke diverters.
  • ERC Series, open-frame with high mechanical performance, for continuous operation.
  • CU Series, square housing and IP40, for dusty environments.
  • Bistable models such as the ERB Series, when the position must be held without power consumption.

In many sorting projects, the final solution is not a catalogue product but custom manufacturing, with the stroke, mounting and connector adapted to the carrier or the station.

Conclusion

In a parcel sorter, the solenoid takes up little space on the drawing and a great deal in the installation’s availability. In mechanical tilt trays and shoe sorters it decides whether the parcel leaves through the right chute; in cross belts it supports the gates, rejects and interlocks that keep the system running. For sorting applications beyond parcels, such as recycling or food processing, see our article on solenoids for selection and sorting machinery.

Frequently asked questions

What is a tilt tray sorter?

It is a sorter made up of carriers with trays that travel around a closed loop. On reaching the assigned outlet, the tray tilts and the parcel slides by gravity into the destination chute. It is used for parcels, envelopes and items of varied formats.

What is the difference between a cross belt sorter and a tilt tray sorter?

The tilt tray discharges by tilting the tray, using gravity. The cross belt discharges with a motorised transverse belt on each carrier, which gives better control over the parcel’s position and handles items that do not slide well.

Why use solenoids instead of pneumatic cylinders in a sorter?

Over short strokes, the solenoid responds faster, is controlled directly from the PLC and needs no compressed air supply. A pneumatic cylinder is preferable when high force is required over long strokes.

How many cycles must a solenoid withstand in a parcel sorter?

It depends on the position, but in tilt tray or shoe sorter diverters several million operations a year is common. That is why the plunger guide and damping are as important as the force.

What IP rating does a solenoid need for postal sorting?

In parcel hubs, with cardboard dust but no water, IP40 covers most positions. In loading docks or exposed installations, a higher rating should be specified.

Please enter your details and you will receive the requested information directly in your email.